Expert Answers about Nissan NV 2500
- How to Complete the 12 Volt Accessory Circuit on the 7-Way of a 2013 Nissan NV 2500
- First thing I would do is check the back of the 7-way to see if there is a wire attached to the 12 volt pin of the 7-way. This will be the 1:00 pin if you are looking into the connector from the front. If a wire is there then most likely you are missing a tow package relay under the hood.
If there is nothing ran to that circuit, (or if you want to just fix the problem without any guesswork) you can run a length of 10 gauge wire from the 12 volt circuit pin of the 7-way through a 40 amp...
view full answer... - How to Use the Curt Echo Trailer Brake Controller on a 2018 Nissan NV 2500
- The brake output (usually blue) wire is not pre ran on all 2018 Nissan NV 2500's. If yours is pre-ran then there will be a brake controller plug which is located under the lower portion of the instrument panel behind the parking brake. If you have the brake controller plug then the brake output wire should be taped to other wires up near the spare tire at the rear but as we have not had the chance to look under a 2018 Nissan NV 2500, I don't have an exact location for you.
With that being...
view full answer... - Using a Generator on a GearDeck 17
- The Gear Deck 17, part # H00604 is able to carry a generator, however, it is not recommended to run the generator with the fully removable lid installed. Our recommended use is to completely remove the lid and unpack the carrier and then use the telescoping base to slide the generator away from your vehicle prior to use.
If your generator does have exhaust that points downward, I recommend removing the generator from the carrier prior to use.
If you are looking to use the generator...
view full answer... - Can Ventline Vanair Trailer Roof Vent Blow Either In or Out
- No the Ventline Vanair Trailer Roof Vent # VP-543SP cannot be configured to run in an opposite direction as intended. While you can use two of these vents they will run in the same direction but do efficiently move 100 cubic feet per minute.
view full answer... - How Does the Tow Ready Custom Fit Vehicle Wiring # 119190KIT Wire to a Vehicle
- To install the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT on your vehicle you will first need to determine what taillight style you have, combined or separate.
Combined taillights mean that the blinkers and stoplights are on the same bulb. Separate means that the brake lights are on a separate bulb from the turn signals. If you have amber turn signals, then most likely you have separate.
If you have combined, you will...
view full answer... - Kit Needed to Install Fan-Tastic Vent Roof Vent
- We have a kit made for installing roof vents, including the Fan-Tastic Vent Roof Vent # FV802250.
What you need is the Roof Vent Installation Kit # 344270KITW.
This kit does include butyl tape, which you'll need, as well as sealant and screws. This kit will work for you no matter if your roof is metal or rubber. I have added a link to a video review of this kit for you to check out.
view full answer... - Installation Location of Engine Block Heater on 2016 Nissan NV2500 with the 5.6L V8
- The Kat's Heaters Custom Engine Block Heater # KH11412 will install in the front right of your 2016 Nissan NV2500 with the 5.6L V8. I've attached a diagram to assist. You will also want to use a thread sealant like # LT37482 or # LT37615.
It is not quite as simple as unscrewing the plug and screwing in the heater, but it is close. You will need to drain your cooling system first because the plug gets immersed in coolant. Other than that, it is basically unscrewing and then screwing...
view full answer...
Go To Results